World Leader in Bullet Swaging Technology
Store Front Account Search Product List Basket Contents Checkout
Sign In (optional)

Choose a category...

Specials
Presses
Bullet Swage Dies
Swage Dies, type -R
Swage Dies,  type -S
Swage Dies, type -H
Specialty Dies
Lead Ball Swage Kits
Bullet Fixer Kits
Jacket Maker Sets
224 / 6mm Swaging Kits
Airgun Swages
50 BMG Tools
Books, Print Editions
Software
Ballistic Test Media
Bullet Tips
Bullet Balls (Polymer)
Bullet Jackets
Chemical Products
Copper Strip/Tube
Lead Wire
Lead Wire Extruders
Core Cutters
Core Moulds
Powder Metal Funnel
Cannelure Tools
Bullet Pullers
Sportswear
Heat Treatment


Delivery Time


Lead Extruder, Small Wire, type -S
 
Lead Extruder, Small Wire, type -S Quantity in Basket: None
Catalog No.: LED-2-S
Price: $298.00
Shipping Weight: 1.50 pounds
 
Select wire diameter:
 
Quantity:
 
LED-2-S Lead Extruder Die for the S-Press makes small diameter wire from .430 wire or .45 caliber lead bullet (soft lead only).

Since the S-Press has a 2-inch swage stroke, and all Corbin hand powered presses develop maximum power at the top of the stroke, the length of the lead "billet" is limited to about 3/4 inch. Longer bits of lead require too much effort for extrusion in one stroke (although you can adjust the die downward a little at a time to use the end of the stroke).

The LED-2-S is best suited for making .100, .125, .170, and .185 diameter wire. The larger the diameter, the shorter the length that can be extruded from a given size of billet (the starting piece of lead is called a billet in an extruder). The LED-2-S makes from one to four inches of wire per stroke, depending on diameter. Fortunately, the calibers that need these small diameter cores only require short lengths.

Hydraulic systems develop full power from the start to finish of the stoke, which is useful for extruding larger billets. The LED-1-H is used in the Corbin Hydro Press CHP-1 to make larger and longer wire sizes from 4 inch long lead cylinders of about 3/4-inch diameter.

Instructions:
The 5/8-24 threaded punch screws into the press ram, finger tight. The 7/8-14 threaded die body screws into the press head (top). Adjust the die position so that the die just begins to project from the bottom side of the press head (you can adjust it further when making the first lead extrusion, for best leverage and complete extrusion).

Put the desired diameter of die insert into the top of the die body, and secure it with the threaded retainer. You can tighten the retainer by hand, firmly, or carefully use a smooth jawed box end wrench. Please do not use pliers, pipe wrench, or other serrated tool to grip and tightern the retainer. The end of the extruder die with the chamfer or "funnel" shape is the one which faces the lead billet (faces down).

Either use a soft lead cast .45 pistol bullet without grease in the grooves, or cast .430 diameter soft lead (Bhn 5) cores of about 3/4-inch length using a Corbin CM-4a core mold. Hard lead will not extrude with safe pressure. Attempting to apply enough pressure to obtain extrusion may destroy the die. When the cores are cool enough to handle, lubricate them with Corbin Swage Lube (CSL-2) by spreading a film of lube on their surface, either by hand (roll between thumb and forefinger with a drop of lube on your fingertip) or by rolling on a stamp pad which has been saturated with lube. If you make them too long, it increases the effort required to extrude, since the longer core engages the press leverage at a lower leverage portion of the stroke. Making them too short does no harm but simply increases the number of times you have to re-load the extruder to get the same total amount of wire length.

Insert a lubricated 3/4-inch long .430 to .450 diameter core, or .45 caliber soft lead pistol bullet, into the bottom of the extruder die. Hold it with one fingeer as needed to slip the extruder punch into the die and take over the support. Raise the ram and see if the die position will let you apply reasonable effort and get extruded wire to come out of the die top. If the effort is too great, raise the position of the die a little at a time until you can extrude wire with firm but not excessive effort. The amount of effort should be about the same as full length resizing a large rifle case (in other words, pressing the handle firmly but not jumping on it).

You cannot make longer wires by adding another billet, and extruding it as part of the previous one. The lead will not stick together. It may extrude a longer wire but the junction probably will be a long, disconnected splice that comes apart when you bend it.

When you have extruded all the wire that will go out the top, there will be a little stem and flange of lead left in the die. Push this out from the top, if you want to make a clean extrusion with another billet. Otherwise there will be a disconnected two-part section of wire that you can't use without it falling apart.



Related Item(s)
Code Name Price Availability  
LED-1-H Lead Wire Extruder, -H $498.00  
LED-1D Lead Wire Extruder Insert, -H $25.00  
LED-2D Lead Wire Extruder Die Insert, type -S $20.00  



EXPORT RESTRICTIONS: We can ONLY ship to USA locations, Canada, or the UK at this time!
Corbins.com
Main Web Site
Swage.com
Document Server
BulletSwage.com
Alternate Site
Swagedies.com
Web Store