World Leader in Bullet Swaging Technology
Store Front Account Search Product List Basket Contents Checkout
Sign In (optional)

Choose a category...

Specials
Presses
Bullet Swage Dies
Swage Dies, type -R
Swage Dies,  type -S
Bullet Swage Sets, -S
Draw Dies, -S
Punches, type -S
Swage Dies, type -H
Specialty Dies
Jacket Maker Sets
224 / 6mm Swaging Kits
Airgun Swages
50 BMG Tools
Books, Print Editions
Software
Ballistic Test Media
Bullet Tips
Bullet Balls (Polymer)
Bullet Jackets
Chemical Products
Copper Strip/Tube
Lead Wire
Lead Wire Extruders
Core Cutters
Core Moulds
Powder Metal Funnel
Cannelure Tools
Bullet Pullers
Sportswear
Heat Treatment


Delivery Time


Catcher Tray for CSP-2, CHP-1 press
 
Catcher Tray for CSP-2, CHP-1 press Quantity in Basket: None
Catalog No.: CHP-T
Price: $22.00
Shipping Weight: 0.80 pounds
 
 
Quantity:
 
The CHP-T Catcher Tray keeps bits of lead extrusions and spent primers from falling on the press top, into the ram slot, and on the floor. It works with your CSP-2 Mega Mite or CHP-1 Hydro Press, with the reloading adapter, Corbin PT-50 priming tool, and any -H type die that extrudes lead to adjust the bullet or core weight (such as the CSW-1-H, LSWC-1-H, or custom weight-adjusting pellet swage and paper-patch swage dies.

The .036-in thick steel unit consists of two sections. The top section has three sides and a bottom with a 1-1/8 inch diameter hole. Your reloading adapter, primer tool, or swage die with 1-in 12 pitch threads slips easily through the hole and screws as usual into the ram, clamping the tray firmly to the top of the ram guide plate.

The lower section is a four-sided box which holds the spent primers or extrusions that otherwise would fall to the top of the press or onto the floor. It keeps the ram free of debris that might otherwise drop through the ram slot.

The use of the catcher tray also blocks the possible high velocity expulsion of bits of lead or other core material which might take place when attempting to swage harder alloys at high pressures. The bleed holes in the dies are lower than the sides of the 3-sided upper section, so that bits of lead blown rapidly from the die holes harmlessly strike the metal side walls and are instantly stopped.

The CHP-T catcher tray also can be "hung" on a 7/8-14 threaded draw die used in the top of the S-press or a standard reloading press, so that the assembly hangs at an angle. This allows bullets or jackets being drawn to emerge from the top of the die and roll into the box section. This makes it faster to draw jackets or bullets since no time is needed to manually catch and move the emerging parts.

The steel unit is powder coated with an oil and grease resistant black finish, and is normally used with the box portion at the rear of the press, but can be mounted in either direction (box forward or to the rear). However, as a safety device to block possible fast expulsion of hard core extrusions, the open back of the top section should be facing away from the operator.

catcher tray

Note:
When used with the Corbin 50 BMG primer tool, the adjustment of the primer seating rod will need to be set .036 inches higher to make up for the thickness of the metal held under the primer adapter body. For nearly any other operation, this makes little or no difference in operation or setting.




EXPORT RESTRICTIONS: We can ONLY ship to USA locations, Canada, or the UK at this time!
Note: 3.5% Bank Card Processing Fee added by Card Processing Service. VCC Number is required for security: send by email with order number.
Corbins.com
Main Web Site
Swage.com
Document Server
BulletSwage.com
Alternate Site
Swagedies.com
Web Store